patch-2.4.6 linux/drivers/mtd/doc2001.c
Next file: linux/drivers/mtd/docecc.c
Previous file: linux/drivers/mtd/doc2000.c
Back to the patch index
Back to the overall index
- Lines: 884
- Date:
Wed Dec 31 16:00:00 1969
- Orig file:
v2.4.5/linux/drivers/mtd/doc2001.c
- Orig date:
Fri Feb 9 11:30:23 2001
diff -u --recursive --new-file v2.4.5/linux/drivers/mtd/doc2001.c linux/drivers/mtd/doc2001.c
@@ -1,883 +0,0 @@
-
-/*
- * Linux driver for Disk-On-Chip Millennium
- * (c) 1999 Machine Vision Holdings, Inc.
- * (c) 1999, 2000 David Woodhouse <dwmw2@infradead.org>
- *
- * $Id: doc2001.c,v 1.24 2000/12/01 13:11:02 dwmw2 Exp $
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <asm/errno.h>
-#include <asm/io.h>
-#include <asm/uaccess.h>
-#include <linux/miscdevice.h>
-#include <linux/pci.h>
-#include <linux/delay.h>
-#include <linux/slab.h>
-#include <linux/sched.h>
-#include <linux/init.h>
-#include <linux/types.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/nand.h>
-#include <linux/mtd/nand_ids.h>
-#include <linux/mtd/doc2000.h>
-
-/* #define ECC_DEBUG */
-
-/* I have no idea why some DoC chips can not use memcop_form|to_io().
- * This may be due to the different revisions of the ASIC controller built-in or
- * simplily a QA/Bug issue. Who knows ?? If you have trouble, please uncomment
- * this:
- #undef USE_MEMCPY
-*/
-
-static int doc_read(struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, u_char *buf);
-static int doc_write(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf);
-static int doc_read_ecc(struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, u_char *buf, u_char *eccbuf);
-static int doc_write_ecc(struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf, u_char *eccbuf);
-static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, size_t len,
- size_t *retlen, u_char *buf);
-static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, size_t len,
- size_t *retlen, const u_char *buf);
-static int doc_erase (struct mtd_info *mtd, struct erase_info *instr);
-
-static struct mtd_info *docmillist = NULL;
-
-/* Perform the required delay cycles by reading from the NOP register */
-static void DoC_Delay(unsigned long docptr, unsigned short cycles)
-{
- volatile char dummy;
- int i;
-
- for (i = 0; i < cycles; i++)
- dummy = ReadDOC(docptr, NOP);
-}
-
-/* DOC_WaitReady: Wait for RDY line to be asserted by the flash chip */
-static int _DoC_WaitReady(unsigned long docptr)
-{
- unsigned short c = 0xffff;
-
- DEBUG(MTD_DEBUG_LEVEL3,
- "_DoC_WaitReady called for out-of-line wait\n");
-
- /* Out-of-line routine to wait for chip response */
- while (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B) && --c)
- ;
-
- if (c == 0)
- DEBUG(MTD_DEBUG_LEVEL2, "_DoC_WaitReady timed out.\n");
-
- return (c == 0);
-}
-
-static inline int DoC_WaitReady(unsigned long docptr)
-{
- /* This is inline, to optimise the common case, where it's ready instantly */
- int ret = 0;
-
- /* 4 read form NOP register should be issued in prior to the read from CDSNControl
- see Software Requirement 11.4 item 2. */
- DoC_Delay(docptr, 4);
-
- if (!(ReadDOC(docptr, CDSNControl) & CDSN_CTRL_FR_B))
- /* Call the out-of-line routine to wait */
- ret = _DoC_WaitReady(docptr);
-
- /* issue 2 read from NOP register after reading from CDSNControl register
- see Software Requirement 11.4 item 2. */
- DoC_Delay(docptr, 2);
-
- return ret;
-}
-
-/* DoC_Command: Send a flash command to the flash chip through the CDSN Slow IO register to
- bypass the internal pipeline. Each of 4 delay cycles (read from the NOP register) is
- required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */
-
-static inline void DoC_Command(unsigned long docptr, unsigned char command,
- unsigned char xtraflags)
-{
- /* Assert the CLE (Command Latch Enable) line to the flash chip */
- WriteDOC(xtraflags | CDSN_CTRL_CLE | CDSN_CTRL_CE, docptr, CDSNControl);
- DoC_Delay(docptr, 4);
-
- /* Send the command */
- WriteDOC(command, docptr, CDSNSlowIO);
- WriteDOC(command, docptr, Mil_CDSN_IO);
-
- /* Lower the CLE line */
- WriteDOC(xtraflags | CDSN_CTRL_CE, docptr, CDSNControl);
- DoC_Delay(docptr, 4);
-}
-
-/* DoC_Address: Set the current address for the flash chip through the CDSN Slow IO register to
- bypass the internal pipeline. Each of 4 delay cycles (read from the NOP register) is
- required after writing to CDSN Control register, see Software Requirement 11.4 item 3. */
-
-static inline void DoC_Address(unsigned long docptr, int numbytes, unsigned long ofs,
- unsigned char xtraflags1, unsigned char xtraflags2)
-{
- /* Assert the ALE (Address Latch Enable) line to the flash chip */
- WriteDOC(xtraflags1 | CDSN_CTRL_ALE | CDSN_CTRL_CE, docptr, CDSNControl);
- DoC_Delay(docptr, 4);
-
- /* Send the address */
- switch (numbytes)
- {
- case 1:
- /* Send single byte, bits 0-7. */
- WriteDOC(ofs & 0xff, docptr, CDSNSlowIO);
- WriteDOC(ofs & 0xff, docptr, Mil_CDSN_IO);
- break;
- case 2:
- /* Send bits 9-16 followed by 17-23 */
- WriteDOC((ofs >> 9) & 0xff, docptr, CDSNSlowIO);
- WriteDOC((ofs >> 9) & 0xff, docptr, Mil_CDSN_IO);
- WriteDOC((ofs >> 17) & 0xff, docptr, CDSNSlowIO);
- WriteDOC((ofs >> 17) & 0xff, docptr, Mil_CDSN_IO);
- break;
- case 3:
- /* Send 0-7, 9-16, then 17-23 */
- WriteDOC(ofs & 0xff, docptr, CDSNSlowIO);
- WriteDOC(ofs & 0xff, docptr, Mil_CDSN_IO);
- WriteDOC((ofs >> 9) & 0xff, docptr, CDSNSlowIO);
- WriteDOC((ofs >> 9) & 0xff, docptr, Mil_CDSN_IO);
- WriteDOC((ofs >> 17) & 0xff, docptr, CDSNSlowIO);
- WriteDOC((ofs >> 17) & 0xff, docptr, Mil_CDSN_IO);
- break;
- default:
- return;
- }
-
- /* Lower the ALE line */
- WriteDOC(xtraflags1 | xtraflags2 | CDSN_CTRL_CE, docptr, CDSNControl);
- DoC_Delay(docptr, 4);
-}
-
-/* DoC_SelectChip: Select a given flash chip within the current floor */
-static int DoC_SelectChip(unsigned long docptr, int chip)
-{
- /* Select the individual flash chip requested */
- WriteDOC(chip, docptr, CDSNDeviceSelect);
- DoC_Delay(docptr, 4);
-
- /* Wait for it to be ready */
- return DoC_WaitReady(docptr);
-}
-
-/* DoC_SelectFloor: Select a given floor (bank of flash chips) */
-static int DoC_SelectFloor(unsigned long docptr, int floor)
-{
- /* Select the floor (bank) of chips required */
- WriteDOC(floor, docptr, FloorSelect);
-
- /* Wait for the chip to be ready */
- return DoC_WaitReady(docptr);
-}
-
-/* DoC_IdentChip: Identify a given NAND chip given {floor,chip} */
-static int DoC_IdentChip(struct DiskOnChip *doc, int floor, int chip)
-{
- int mfr, id, i;
- volatile char dummy;
-
- /* Page in the required floor/chip
- FIXME: is this supported by Millennium ?? */
- DoC_SelectFloor(doc->virtadr, floor);
- DoC_SelectChip(doc->virtadr, chip);
-
- /* Reset the chip, see Software Requirement 11.4 item 1. */
- DoC_Command(doc->virtadr, NAND_CMD_RESET, CDSN_CTRL_WP);
- DoC_WaitReady(doc->virtadr);
-
- /* Read the NAND chip ID: 1. Send ReadID command */
- DoC_Command(doc->virtadr, NAND_CMD_READID, CDSN_CTRL_WP);
-
- /* Read the NAND chip ID: 2. Send address byte zero */
- DoC_Address(doc->virtadr, 1, 0x00, CDSN_CTRL_WP, 0x00);
-
- /* Read the manufacturer and device id codes of the flash device through
- CDSN Slow IO register see Software Requirement 11.4 item 5.*/
- dummy = ReadDOC(doc->virtadr, CDSNSlowIO);
- DoC_Delay(doc->virtadr, 2);
- mfr = ReadDOC(doc->virtadr, Mil_CDSN_IO);
-
- dummy = ReadDOC(doc->virtadr, CDSNSlowIO);
- DoC_Delay(doc->virtadr, 2);
- id = ReadDOC(doc->virtadr, Mil_CDSN_IO);
-
- /* No response - return failure */
- if (mfr == 0xff || mfr == 0)
- return 0;
-
- /* FIXME: to deal with multi-flash on multi-Millennium case more carefully */
- for (i = 0; nand_flash_ids[i].name != NULL; i++) {
- if (mfr == nand_flash_ids[i].manufacture_id &&
- id == nand_flash_ids[i].model_id) {
- printk(KERN_INFO "Flash chip found: Manufacturer ID: %2.2X, "
- "Chip ID: %2.2X (%s)\n",
- mfr, id, nand_flash_ids[i].name);
- doc->mfr = mfr;
- doc->id = id;
- doc->chipshift = nand_flash_ids[i].chipshift;
- break;
- }
- }
-
- if (nand_flash_ids[i].name == NULL)
- return 0;
- else
- return 1;
-}
-
-/* DoC_ScanChips: Find all NAND chips present in a DiskOnChip, and identify them */
-static void DoC_ScanChips(struct DiskOnChip *this)
-{
- int floor, chip;
- int numchips[MAX_FLOORS_MIL];
- int ret;
-
- this->numchips = 0;
- this->mfr = 0;
- this->id = 0;
-
- /* For each floor, find the number of valid chips it contains */
- for (floor = 0,ret = 1; floor < MAX_FLOORS_MIL; floor++) {
- numchips[floor] = 0;
- for (chip = 0; chip < MAX_CHIPS_MIL && ret != 0; chip++) {
- ret = DoC_IdentChip(this, floor, chip);
- if (ret) {
- numchips[floor]++;
- this->numchips++;
- }
- }
- }
- /* If there are none at all that we recognise, bail */
- if (!this->numchips) {
- printk("No flash chips recognised.\n");
- return;
- }
-
- /* Allocate an array to hold the information for each chip */
- this->chips = kmalloc(sizeof(struct Nand) * this->numchips, GFP_KERNEL);
- if (!this->chips){
- printk("No memory for allocating chip info structures\n");
- return;
- }
-
- /* Fill out the chip array with {floor, chipno} for each
- * detected chip in the device. */
- for (floor = 0, ret = 0; floor < MAX_FLOORS_MIL; floor++) {
- for (chip = 0 ; chip < numchips[floor] ; chip++) {
- this->chips[ret].floor = floor;
- this->chips[ret].chip = chip;
- this->chips[ret].curadr = 0;
- this->chips[ret].curmode = 0x50;
- ret++;
- }
- }
-
- /* Calculate and print the total size of the device */
- this->totlen = this->numchips * (1 << this->chipshift);
- printk(KERN_NOTICE "%d flash chips found. Total DiskOnChip size: %ld Mbytes\n",
- this->numchips ,this->totlen >> 20);
-}
-
-static int DoCMil_is_alias(struct DiskOnChip *doc1, struct DiskOnChip *doc2)
-{
- int tmp1, tmp2, retval;
-
- if (doc1->physadr == doc2->physadr)
- return 1;
-
- /* Use the alias resolution register which was set aside for this
- * purpose. If it's value is the same on both chips, they might
- * be the same chip, and we write to one and check for a change in
- * the other. It's unclear if this register is usuable in the
- * DoC 2000 (it's in the Millenium docs), but it seems to work. */
- tmp1 = ReadDOC(doc1->virtadr, AliasResolution);
- tmp2 = ReadDOC(doc2->virtadr, AliasResolution);
- if (tmp1 != tmp2)
- return 0;
-
- WriteDOC((tmp1+1) % 0xff, doc1->virtadr, AliasResolution);
- tmp2 = ReadDOC(doc2->virtadr, AliasResolution);
- if (tmp2 == (tmp1+1) % 0xff)
- retval = 1;
- else
- retval = 0;
-
- /* Restore register contents. May not be necessary, but do it just to
- * be safe. */
- WriteDOC(tmp1, doc1->virtadr, AliasResolution);
-
- return retval;
-}
-
-static const char im_name[] = "DoCMil_init";
-
-/* This routine is made available to other mtd code via
- * inter_module_register. It must only be accessed through
- * inter_module_get which will bump the use count of this module. The
- * addresses passed back in mtd are valid as long as the use count of
- * this module is non-zero, i.e. between inter_module_get and
- * inter_module_put. Keith Owens <kaos@ocs.com.au> 29 Oct 2000.
- */
-static void DoCMil_init(struct mtd_info *mtd)
-{
- struct DiskOnChip *this = (struct DiskOnChip *)mtd->priv;
- struct DiskOnChip *old = NULL;
-
- /* We must avoid being called twice for the same device. */
- if (docmillist)
- old = (struct DiskOnChip *)docmillist->priv;
-
- while (old) {
- if (DoCMil_is_alias(this, old)) {
- printk(KERN_NOTICE "Ignoring DiskOnChip Millennium at "
- "0x%lX - already configured\n", this->physadr);
- iounmap((void *)this->virtadr);
- kfree(mtd);
- return;
- }
- if (old->nextdoc)
- old = (struct DiskOnChip *)old->nextdoc->priv;
- else
- old = NULL;
- }
-
- mtd->name = "DiskOnChip Millennium";
- printk(KERN_NOTICE "DiskOnChip Millennium found at address 0x%lX\n",
- this->physadr);
-
- mtd->type = MTD_NANDFLASH;
- mtd->flags = MTD_CAP_NANDFLASH;
- mtd->size = 0;
-
- /* FIXME: erase size is not always 8kB */
- mtd->erasesize = 0x2000;
-
- mtd->oobblock = 512;
- mtd->oobsize = 16;
- mtd->module = THIS_MODULE;
- mtd->erase = doc_erase;
- mtd->point = NULL;
- mtd->unpoint = NULL;
- mtd->read = doc_read;
- mtd->write = doc_write;
- mtd->read_ecc = doc_read_ecc;
- mtd->write_ecc = doc_write_ecc;
- mtd->read_oob = doc_read_oob;
- mtd->write_oob = doc_write_oob;
- mtd->sync = NULL;
-
- this->totlen = 0;
- this->numchips = 0;
- this->curfloor = -1;
- this->curchip = -1;
-
- /* Ident all the chips present. */
- DoC_ScanChips(this);
-
- if (!this->totlen) {
- kfree(mtd);
- iounmap((void *)this->virtadr);
- } else {
- this->nextdoc = docmillist;
- docmillist = mtd;
- mtd->size = this->totlen;
- add_mtd_device(mtd);
- return;
- }
-}
-
-static int doc_read (struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, u_char *buf)
-{
- /* Just a special case of doc_read_ecc */
- return doc_read_ecc(mtd, from, len, retlen, buf, NULL);
-}
-
-static int doc_read_ecc (struct mtd_info *mtd, loff_t from, size_t len,
- size_t *retlen, u_char *buf, u_char *eccbuf)
-{
- int i, ret;
- volatile char dummy;
- unsigned char syndrome[6];
- struct DiskOnChip *this = (struct DiskOnChip *)mtd->priv;
- unsigned long docptr = this->virtadr;
- struct Nand *mychip = &this->chips[from >> (this->chipshift)];
-
- /* Don't allow read past end of device */
- if (from >= this->totlen)
- return -EINVAL;
-
- /* Don't allow a single read to cross a 512-byte block boundary */
- if (from + len > ((from | 0x1ff) + 1))
- len = ((from | 0x1ff) + 1) - from;
-
- /* Find the chip which is to be used and select it */
- if (this->curfloor != mychip->floor) {
- DoC_SelectFloor(docptr, mychip->floor);
- DoC_SelectChip(docptr, mychip->chip);
- } else if (this->curchip != mychip->chip) {
- DoC_SelectChip(docptr, mychip->chip);
- }
- this->curfloor = mychip->floor;
- this->curchip = mychip->chip;
-
- /* issue the Read0 or Read1 command depend on which half of the page
- we are accessing. Polling the Flash Ready bit after issue 3 bytes
- address in Sequence Read Mode, see Software Requirement 11.4 item 1.*/
- DoC_Command(docptr, (from >> 8) & 1, CDSN_CTRL_WP);
- DoC_Address(docptr, 3, from, CDSN_CTRL_WP, 0x00);
- DoC_WaitReady(docptr);
-
- if (eccbuf) {
- /* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/
- WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
- WriteDOC (DOC_ECC_EN, docptr, ECCConf);
- } else {
- /* disable the ECC engine */
- WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
- WriteDOC (DOC_ECC_DIS, docptr, ECCConf);
- }
-
- /* Read the data via the internal pipeline through CDSN IO register,
- see Pipelined Read Operations 11.3 */
- dummy = ReadDOC(docptr, ReadPipeInit);
-#ifndef USE_MEMCPY
- for (i = 0; i < len-1; i++) {
- /* N.B. you have to increase the source address in this way or the
- ECC logic will not work properly */
- buf[i] = ReadDOC(docptr, Mil_CDSN_IO + (i & 0xff));
- }
-#else
- memcpy_fromio(buf, docptr + DoC_Mil_CDSN_IO, len - 1);
-#endif
- buf[len - 1] = ReadDOC(docptr, LastDataRead);
-
- /* Let the caller know we completed it */
- *retlen = len;
- ret = 0;
-
- if (eccbuf) {
- /* Read the ECC data from Spare Data Area,
- see Reed-Solomon EDC/ECC 11.1 */
- dummy = ReadDOC(docptr, ReadPipeInit);
-#ifndef USE_MEMCPY
- for (i = 0; i < 5; i++) {
- /* N.B. you have to increase the source address in this way or the
- ECC logic will not work properly */
- eccbuf[i] = ReadDOC(docptr, Mil_CDSN_IO + i);
- }
-#else
- memcpy_fromio(eccbuf, docptr + DoC_Mil_CDSN_IO, 5);
-#endif
- eccbuf[5] = ReadDOC(docptr, LastDataRead);
-
- /* Flush the pipeline */
- dummy = ReadDOC(docptr, ECCConf);
- dummy = ReadDOC(docptr, ECCConf);
-
- /* Check the ECC Status */
- if (ReadDOC(docptr, ECCConf) & 0x80) {
- int nb_errors;
- /* There was an ECC error */
-#ifdef ECC_DEBUG
- printk("DiskOnChip ECC Error: Read at %lx\n", (long)from);
-#endif
- /* Read the ECC syndrom through the DiskOnChip ECC logic.
- These syndrome will be all ZERO when there is no error */
- for (i = 0; i < 6; i++) {
- syndrome[i] = ReadDOC(docptr, ECCSyndrome0 + i);
- }
- nb_errors = doc_decode_ecc(buf, syndrome);
-#ifdef ECC_DEBUG
- printk("Errors corrected: %x\n", nb_errors);
-#endif
- if (nb_errors < 0) {
- /* We return error, but have actually done the read. Not that
- this can be told to user-space, via sys_read(), but at least
- MTD-aware stuff can know about it by checking *retlen */
- ret = -EIO;
- }
- }
-
-#ifdef PSYCHO_DEBUG
- printk("ECC DATA at %lx: %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n",
- (long)from, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3],
- eccbuf[4], eccbuf[5]);
-#endif
- /* disable the ECC engine */
- WriteDOC(DOC_ECC_DIS, docptr , ECCConf);
- }
-
- return ret;
-}
-
-static int doc_write (struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf)
-{
- char eccbuf[6];
- return doc_write_ecc(mtd, to, len, retlen, buf, eccbuf);
-}
-
-static int doc_write_ecc (struct mtd_info *mtd, loff_t to, size_t len,
- size_t *retlen, const u_char *buf, u_char *eccbuf)
-{
- int i;
- volatile char dummy;
- struct DiskOnChip *this = (struct DiskOnChip *)mtd->priv;
- unsigned long docptr = this->virtadr;
- struct Nand *mychip = &this->chips[to >> (this->chipshift)];
-
- /* Don't allow write past end of device */
- if (to >= this->totlen)
- return -EINVAL;
-
-#if 0
- /* Don't allow a single write to cross a 512-byte block boundary */
- if (to + len > ( (to | 0x1ff) + 1))
- len = ((to | 0x1ff) + 1) - to;
-#else
- /* Don't allow writes which aren't exactly one block */
- if (to & 0x1ff || len != 0x200)
- return -EINVAL;
-#endif
-
- /* Find the chip which is to be used and select it */
- if (this->curfloor != mychip->floor) {
- DoC_SelectFloor(docptr, mychip->floor);
- DoC_SelectChip(docptr, mychip->chip);
- } else if (this->curchip != mychip->chip) {
- DoC_SelectChip(docptr, mychip->chip);
- }
- this->curfloor = mychip->floor;
- this->curchip = mychip->chip;
-
- /* Reset the chip, see Software Requirement 11.4 item 1. */
- DoC_Command(docptr, NAND_CMD_RESET, 0x00);
- DoC_WaitReady(docptr);
- /* Set device to main plane of flash */
- DoC_Command(docptr, NAND_CMD_READ0, 0x00);
-
- /* issue the Serial Data In command to initial the Page Program process */
- DoC_Command(docptr, NAND_CMD_SEQIN, 0x00);
- DoC_Address(docptr, 3, to, 0x00, 0x00);
- DoC_WaitReady(docptr);
-
- if (eccbuf) {
- /* init the ECC engine, see Reed-Solomon EDC/ECC 11.1 .*/
- WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
- WriteDOC (DOC_ECC_EN | DOC_ECC_RW, docptr, ECCConf);
- } else {
- /* disable the ECC engine */
- WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
- WriteDOC (DOC_ECC_DIS, docptr, ECCConf);
- }
-
- /* Write the data via the internal pipeline through CDSN IO register,
- see Pipelined Write Operations 11.2 */
-#ifndef USE_MEMCPY
- for (i = 0; i < len; i++) {
- /* N.B. you have to increase the source address in this way or the
- ECC logic will not work properly */
- WriteDOC(buf[i], docptr, Mil_CDSN_IO + i);
- }
-#else
- memcpy_toio(docptr + DoC_Mil_CDSN_IO, buf, len);
-#endif
- WriteDOC(0x00, docptr, WritePipeTerm);
-
- if (eccbuf) {
- /* Write ECC data to flash, the ECC info is generated by the DiskOnChip ECC logic
- see Reed-Solomon EDC/ECC 11.1 */
- WriteDOC(0, docptr, NOP);
- WriteDOC(0, docptr, NOP);
- WriteDOC(0, docptr, NOP);
-
- /* Read the ECC data through the DiskOnChip ECC logic */
- for (i = 0; i < 6; i++) {
- eccbuf[i] = ReadDOC(docptr, ECCSyndrome0 + i);
- }
-
- /* ignore the ECC engine */
- WriteDOC(DOC_ECC_DIS, docptr , ECCConf);
-
-#ifndef USE_MEMCPY
- /* Write the ECC data to flash */
- for (i = 0; i < 6; i++) {
- /* N.B. you have to increase the source address in this way or the
- ECC logic will not work properly */
- WriteDOC(eccbuf[i], docptr, Mil_CDSN_IO + i);
- }
-#else
- memcpy_toio(docptr + DoC_Mil_CDSN_IO, eccbuf, 6);
-#endif
-
- /* write the block status BLOCK_USED (0x5555) at the end of ECC data
- FIXME: this is only a hack for programming the IPL area for LinuxBIOS
- and should be replace with proper codes in user space utilities */
- WriteDOC(0x55, docptr, Mil_CDSN_IO);
- WriteDOC(0x55, docptr, Mil_CDSN_IO + 1);
-
- WriteDOC(0x00, docptr, WritePipeTerm);
-
-#ifdef PSYCHO_DEBUG
- printk("OOB data at %lx is %2.2X %2.2X %2.2X %2.2X %2.2X %2.2X\n",
- (long) to, eccbuf[0], eccbuf[1], eccbuf[2], eccbuf[3],
- eccbuf[4], eccbuf[5]);
-#endif
- }
-
- /* Commit the Page Program command and wait for ready
- see Software Requirement 11.4 item 1.*/
- DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00);
- DoC_WaitReady(docptr);
-
- /* Read the status of the flash device through CDSN Slow IO register
- see Software Requirement 11.4 item 5.*/
- DoC_Command(docptr, NAND_CMD_STATUS, CDSN_CTRL_WP);
- dummy = ReadDOC(docptr, CDSNSlowIO);
- DoC_Delay(docptr, 2);
- if (ReadDOC(docptr, Mil_CDSN_IO) & 1) {
- printk("Error programming flash\n");
- /* Error in programming
- FIXME: implement Bad Block Replacement (in nftl.c ??) */
- *retlen = 0;
- return -EIO;
- }
-
- /* Let the caller know we completed it */
- *retlen = len;
-
- return 0;
-}
-
-static int doc_read_oob(struct mtd_info *mtd, loff_t ofs, size_t len,
- size_t *retlen, u_char *buf)
-{
-#ifndef USE_MEMCPY
- int i;
-#endif
- volatile char dummy;
- struct DiskOnChip *this = (struct DiskOnChip *)mtd->priv;
- unsigned long docptr = this->virtadr;
- struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-
- /* Find the chip which is to be used and select it */
- if (this->curfloor != mychip->floor) {
- DoC_SelectFloor(docptr, mychip->floor);
- DoC_SelectChip(docptr, mychip->chip);
- } else if (this->curchip != mychip->chip) {
- DoC_SelectChip(docptr, mychip->chip);
- }
- this->curfloor = mychip->floor;
- this->curchip = mychip->chip;
-
- /* disable the ECC engine */
- WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
- WriteDOC (DOC_ECC_DIS, docptr, ECCConf);
-
- /* issue the Read2 command to set the pointer to the Spare Data Area.
- Polling the Flash Ready bit after issue 3 bytes address in
- Sequence Read Mode, see Software Requirement 11.4 item 1.*/
- DoC_Command(docptr, NAND_CMD_READOOB, CDSN_CTRL_WP);
- DoC_Address(docptr, 3, ofs, CDSN_CTRL_WP, 0x00);
- DoC_WaitReady(docptr);
-
- /* Read the data out via the internal pipeline through CDSN IO register,
- see Pipelined Read Operations 11.3 */
- dummy = ReadDOC(docptr, ReadPipeInit);
-#ifndef USE_MEMCPY
- for (i = 0; i < len-1; i++) {
- /* N.B. you have to increase the source address in this way or the
- ECC logic will not work properly */
- buf[i] = ReadDOC(docptr, Mil_CDSN_IO + i);
- }
- buf[i] = ReadDOC(docptr, LastDataRead);
-#else
- memcpy_fromio(buf, docptr + DoC_Mil_CDSN_IO, len - 1);
-#endif
- buf[len - 1] = ReadDOC(docptr, LastDataRead);
-
- *retlen = len;
-
- return 0;
-}
-
-static int doc_write_oob(struct mtd_info *mtd, loff_t ofs, size_t len,
- size_t *retlen, const u_char *buf)
-{
-#ifndef USE_MEMCPY
- int i;
-#endif
- volatile char dummy;
- struct DiskOnChip *this = (struct DiskOnChip *)mtd->priv;
- unsigned long docptr = this->virtadr;
- struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-
- /* Find the chip which is to be used and select it */
- if (this->curfloor != mychip->floor) {
- DoC_SelectFloor(docptr, mychip->floor);
- DoC_SelectChip(docptr, mychip->chip);
- } else if (this->curchip != mychip->chip) {
- DoC_SelectChip(docptr, mychip->chip);
- }
- this->curfloor = mychip->floor;
- this->curchip = mychip->chip;
-
- /* disable the ECC engine */
- WriteDOC (DOC_ECC_RESET, docptr, ECCConf);
- WriteDOC (DOC_ECC_DIS, docptr, ECCConf);
-
- /* Reset the chip, see Software Requirement 11.4 item 1. */
- DoC_Command(docptr, NAND_CMD_RESET, CDSN_CTRL_WP);
- DoC_WaitReady(docptr);
- /* issue the Read2 command to set the pointer to the Spare Data Area. */
- DoC_Command(docptr, NAND_CMD_READOOB, CDSN_CTRL_WP);
-
- /* issue the Serial Data In command to initial the Page Program process */
- DoC_Command(docptr, NAND_CMD_SEQIN, 0x00);
- DoC_Address(docptr, 3, ofs, 0x00, 0x00);
-
- /* Write the data via the internal pipeline through CDSN IO register,
- see Pipelined Write Operations 11.2 */
-#ifndef USE_MEMCPY
- for (i = 0; i < len; i++) {
- /* N.B. you have to increase the source address in this way or the
- ECC logic will not work properly */
- WriteDOC(buf[i], docptr, Mil_CDSN_IO + i);
- }
-#else
- memcpy_toio(docptr + DoC_Mil_CDSN_IO, buf, len);
-#endif
- WriteDOC(0x00, docptr, WritePipeTerm);
-
- /* Commit the Page Program command and wait for ready
- see Software Requirement 11.4 item 1.*/
- DoC_Command(docptr, NAND_CMD_PAGEPROG, 0x00);
- DoC_WaitReady(docptr);
-
- /* Read the status of the flash device through CDSN Slow IO register
- see Software Requirement 11.4 item 5.*/
- DoC_Command(docptr, NAND_CMD_STATUS, 0x00);
- dummy = ReadDOC(docptr, CDSNSlowIO);
- DoC_Delay(docptr, 2);
- if (ReadDOC(docptr, Mil_CDSN_IO) & 1) {
- printk("Error programming oob data\n");
- /* FIXME: implement Bad Block Replacement (in nftl.c ??) */
- *retlen = 0;
- return -EIO;
- }
-
- *retlen = len;
-
- return 0;
-}
-
-int doc_erase (struct mtd_info *mtd, struct erase_info *instr)
-{
- volatile char dummy;
- struct DiskOnChip *this = (struct DiskOnChip *)mtd->priv;
- unsigned long ofs = instr->addr;
- unsigned long len = instr->len;
- unsigned long docptr = this->virtadr;
- struct Nand *mychip = &this->chips[ofs >> this->chipshift];
-
- if (len != mtd->erasesize)
- printk(KERN_WARNING "Erase not right size (%lx != %lx)n",
- len, mtd->erasesize);
-
- /* Find the chip which is to be used and select it */
- if (this->curfloor != mychip->floor) {
- DoC_SelectFloor(docptr, mychip->floor);
- DoC_SelectChip(docptr, mychip->chip);
- } else if (this->curchip != mychip->chip) {
- DoC_SelectChip(docptr, mychip->chip);
- }
- this->curfloor = mychip->floor;
- this->curchip = mychip->chip;
-
- instr->state = MTD_ERASE_PENDING;
-
- /* issue the Erase Setup command */
- DoC_Command(docptr, NAND_CMD_ERASE1, 0x00);
- DoC_Address(docptr, 2, ofs, 0x00, 0x00);
-
- /* Commit the Erase Start command and wait for ready
- see Software Requirement 11.4 item 1.*/
- DoC_Command(docptr, NAND_CMD_ERASE2, 0x00);
- DoC_WaitReady(docptr);
-
- instr->state = MTD_ERASING;
-
- /* Read the status of the flash device through CDSN Slow IO register
- see Software Requirement 11.4 item 5.
- FIXME: it seems that we are not wait long enough, some blocks are not
- erased fully */
- DoC_Command(docptr, NAND_CMD_STATUS, CDSN_CTRL_WP);
- dummy = ReadDOC(docptr, CDSNSlowIO);
- DoC_Delay(docptr, 2);
- if (ReadDOC(docptr, Mil_CDSN_IO) & 1) {
- printk("Error Erasing at 0x%lx\n", ofs);
- /* There was an error
- FIXME: implement Bad Block Replacement (in nftl.c ??) */
- instr->state = MTD_ERASE_FAILED;
- } else
- instr->state = MTD_ERASE_DONE;
-
- if (instr->callback)
- instr->callback(instr);
-
- return 0;
-}
-
-/****************************************************************************
- *
- * Module stuff
- *
- ****************************************************************************/
-
-#if LINUX_VERSION_CODE < 0x20212 && defined(MODULE)
-#define cleanup_doc2001 cleanup_module
-#define init_doc2001 init_module
-#endif
-
-int __init init_doc2001(void)
-{
- inter_module_register(im_name, THIS_MODULE, &DoCMil_init);
- return 0;
-}
-
-static void __exit cleanup_doc2001(void)
-{
- struct mtd_info *mtd;
- struct DiskOnChip *this;
-
- while((mtd=docmillist)) {
- this = (struct DiskOnChip *)mtd->priv;
- docmillist = this->nextdoc;
-
- del_mtd_device(mtd);
-
- iounmap((void *)this->virtadr);
- kfree(this->chips);
- kfree(mtd);
- }
- inter_module_unregister(im_name);
-}
-
-module_exit(cleanup_doc2001);
-module_init(init_doc2001);
-
-
FUNET's LINUX-ADM group, linux-adm@nic.funet.fi
TCL-scripts by Sam Shen (who was at: slshen@lbl.gov)