RFC 9006 TCP in IoT March 2021
Gomez, et al. Informational [Page]
Stream:
Internet Engineering Task Force (IETF)
RFC:
9006
Category:
Informational
Published:
ISSN:
2070-1721
Authors:
C. Gomez
UPC
J. Crowcroft
University of Cambridge
M. Scharf
Hochschule Esslingen

RFC 9006

TCP Usage Guidance in the Internet of Things (IoT)

Abstract

This document provides guidance on how to implement and use the Transmission Control Protocol (TCP) in Constrained-Node Networks (CNNs), which are a characteristic of the Internet of Things (IoT). Such environments require a lightweight TCP implementation and may not make use of optional functionality. This document explains a number of known and deployed techniques to simplify a TCP stack as well as corresponding trade-offs. The objective is to help embedded developers with decisions on which TCP features to use.

Status of This Memo

This document is not an Internet Standards Track specification; it is published for informational purposes.

This document is a product of the Internet Engineering Task Force (IETF). It represents the consensus of the IETF community. It has received public review and has been approved for publication by the Internet Engineering Steering Group (IESG). Not all documents approved by the IESG are candidates for any level of Internet Standard; see Section 2 of RFC 7841.

Information about the current status of this document, any errata, and how to provide feedback on it may be obtained at https://www.rfc-editor.org/info/rfc9006.

Table of Contents

1. Introduction

The Internet Protocol suite is being used for connecting Constrained-Node Networks (CNNs) to the Internet, enabling the so-called Internet of Things (IoT) [RFC7228]. In order to meet the requirements that stem from CNNs, the IETF has produced a suite of new protocols specifically designed for such environments (see, e.g., [RFC8352]). New IETF protocol stack components include the IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs) adaptation layer [RFC4944][RFC6282][RFC6775], the IPv6 Routing Protocol for Low-Power and Lossy Networks (RPL) [RFC6550], and the Constrained Application Protocol (CoAP) [RFC7252].

As of this writing, the main transport-layer protocols in IP-based IoT scenarios are UDP and TCP. TCP has been criticized, often unfairly, as a protocol that is unsuitable for the IoT. It is true that some TCP features, such as relatively long header size, unsuitability for multicast, and always-confirmed data delivery, are not optimal for IoT scenarios. However, many typical claims on TCP unsuitability for IoT (e.g., a high complexity, connection-oriented approach incompatibility with radio duty-cycling and spurious congestion control activation in wireless links) are not valid, can be solved, or are also found in well-accepted IoT end-to-end reliability mechanisms (see a detailed analysis in [IntComp]).

At the application layer, CoAP was developed over UDP [RFC7252]. However, the integration of some CoAP deployments with existing infrastructure is being challenged by middleboxes such as firewalls, which may limit and even block UDP-based communications. This is the main reason why a CoAP over TCP specification has been developed [RFC8323].

Other application-layer protocols not specifically designed for CNNs are also being considered for the IoT space. Some examples include HTTP/2 and even HTTP/1.1, both of which run over TCP by default [RFC7230] [RFC7540], and the Extensible Messaging and Presence Protocol (XMPP) [RFC6120]. TCP is also used by non-IETF application-layer protocols in the IoT space such as the Message Queuing Telemetry Transport (MQTT) [MQTT] and its lightweight variants.

TCP is a sophisticated transport protocol that includes optional functionality (e.g., TCP options) that may improve performance in some environments. However, many optional TCP extensions require complex logic inside the TCP stack and increase the code size and the memory requirements. Many TCP extensions are not required for interoperability with other standard-compliant TCP endpoints. Given the limited resources on constrained devices, careful selection of optional TCP features can make an implementation more lightweight.

This document provides guidance on how to implement and configure TCP and guidance on how applications should use TCP in CNNs. The overarching goal is to offer simple measures to allow for lightweight TCP implementation and suitable operation in such environments. A TCP implementation following the guidance in this document is intended to be compatible with a TCP endpoint that is compliant to the TCP standards, albeit possibly with a lower performance. This implies that such a TCP client would always be able to connect with a standard-compliant TCP server, and a corresponding TCP server would always be able to connect with a standard-compliant TCP client.

This document assumes that the reader is familiar with TCP. A comprehensive survey of the TCP standards can be found in RFC 7414 [RFC7414]. Similar guidance regarding the use of TCP in special environments has been published before, e.g., for cellular wireless networks [RFC3481].

2. Characteristics of CNNs Relevant for TCP

CNNs are defined in [RFC7228] as networks whose characteristics are influenced by being composed of a significant portion of constrained nodes. The latter are characterized by significant limitations on processing, memory, and energy resources, among others [RFC7228]. The first two dimensions pose constraints on the complexity and memory footprint of the protocols that constrained nodes can support. The latter requires techniques to save energy, such as radio duty-cycling in wireless devices [RFC8352] and the minimization of the number of messages transmitted/received (and their size).

[RFC7228] lists typical network constraints in CNNs, including low achievable bitrate/throughput, high packet loss and high variability of packet loss, highly asymmetric link characteristics, severe penalties for using larger packets, limits on reachability over time, etc. CNNs may use wireless or wired technologies (e.g., Power Line Communication), and the transmission rates are typically low (e.g., below 1 Mbps).

For use of TCP, one challenge is that not all technologies in a CNN may be aligned with typical Internet subnetwork design principles [RFC3819]. For instance, constrained nodes often use physical- / link-layer technologies that have been characterized as 'lossy', i.e., exhibit a relatively high bit error rate. Dealing with corruption loss is one of the open issues in the Internet [RFC6077].

2.2. Usage Scenarios

There are different deployment and usage scenarios for CNNs. Some CNNs follow the star topology, whereby one or several hosts are linked to a central device that acts as a router connecting the CNN to the Internet. Alternatively, CNNs may also follow the multihop topology [RFC6606].

In constrained environments, there can be different types of devices [RFC7228]. For example, there can be devices with a single combined send/receive buffer, a separate send and receive buffer, or a pool of multiple send/receive buffers. In the latter case, it is possible that buffers are also shared for other protocols.

One key use case for TCP in CNNs is a model where constrained devices connect to unconstrained servers in the Internet. But it is also possible that both TCP endpoints run on constrained devices. In the first case, communication will possibly traverse a middlebox (e.g., a firewall, NAT, etc.). Figure 1 illustrates such a scenario. Note that the scenario is asymmetric, as the unconstrained device will typically not suffer the severe constraints of the constrained device. The unconstrained device is expected to be mains-powered, have a high amount of memory and processing power, and be connected to a resource-rich network.

Assuming that a majority of constrained devices will correspond to sensor nodes, the amount of data traffic sent by constrained devices (e.g., sensor node measurements) is expected to be higher than the amount of data traffic in the opposite direction. Nevertheless, constrained devices may receive requests (to which they may respond), commands (for configuration purposes and for constrained devices including actuators), and relatively infrequent firmware/software updates.

                                                   +---------------+
        o     o <-------- TCP communication -----> |               |
       o     o                                     |               |
          o     o                                  | Unconstrained |
    o        o              +-----------+          |    device     |
        o     o   o  ------ | Middlebox |  ------- |               |
         o   o              +-----------+          | (e.g., cloud) |
       o    o  o                                   |               |
                                                   +---------------+
   Constrained devices
Figure 1: TCP Communication between a Constrained Device and an Unconstrained Device, Traversing a Middlebox

2.3. Communication and Traffic Patterns

IoT applications are characterized by a number of different communication patterns. The following non-comprehensive list explains some typical examples:

Unidirectional transfers:
An IoT device (e.g., a sensor) can (repeatedly) send updates to the other endpoint. There is not always a need for an application response back to the IoT device.
Request-response patterns:
An IoT device receiving a request from the other endpoint, which triggers a response from the IoT device.
Bulk data transfers:
A typical example for a long file transfer would be an IoT device firmware update.

A typical communication pattern is that a constrained device communicates with an unconstrained device (cf. Figure 1). But it is also possible that constrained devices communicate amongst themselves.

3. TCP Implementation and Configuration in CNNs

This section explains how a TCP stack can deal with typical constraints in CNN. The guidance in this section relates to the TCP implementation and its configuration.

3.1. Addressing Path Properties

3.1.1. Maximum Segment Size (MSS)

Assuming that IPv6 is used, and for the sake of lightweight implementation and operation, unless applications require handling large data units (i.e., leading to an IPv6 datagram size greater than 1280 bytes), it may be desirable to limit the IP datagram size to 1280 bytes in order to avoid the need to support Path MTU Discovery [RFC8201]. In addition, an IP datagram size of 1280 bytes avoids incurring IPv6-layer fragmentation [RFC8900].

An IPv6 datagram size exceeding 1280 bytes can be avoided by setting the TCP MSS to 1220 bytes or less. Note that it is already a requirement for TCP implementations to consume payload space instead of increasing datagram size when including IP or TCP options in an IP packet to be sent [RFC6691]. Therefore, it is not required to advertise an MSS smaller than 1220 bytes in order to accommodate TCP options.

Note that setting the MTU to 1280 bytes is possible for link-layer technologies in the CNN space, even if some of them are characterized by a short data unit payload size, e.g., up to a few tens or hundreds of bytes. For example, the maximum frame size in IEEE 802.15.4 is 127 bytes. 6LoWPAN defined an adaptation layer to support IPv6 over IEEE 802.15.4 networks. The adaptation layer includes a fragmentation mechanism, since IPv6 requires the layer below to support an MTU of 1280 bytes [RFC8200], while IEEE 802.15.4 lacks fragmentation mechanisms. 6LoWPAN defines an IEEE 802.15.4 link MTU of 1280 bytes [RFC4944]. Other technologies, such as Bluetooth low energy [RFC7668], ITU-T G.9959 [RFC7428], or Digital Enhanced Cordless Telecommunications (DECT) Ultra Low Energy (ULE) [RFC8105], also use 6LoWPAN-based adaptation layers in order to enable IPv6 support. These technologies do support link-layer fragmentation. By exploiting this functionality, the adaptation layers that enable IPv6 over such technologies also define an MTU of 1280 bytes.

On the other hand, there exist technologies also used in the CNN space, such as Master Slave (MS) / Token Passing (TP) [RFC8163], Narrowband IoT (NB-IoT) [RFC8376], or IEEE 802.11ah [6LO-WLANAH], that do not suffer the same degree of frame size limitations as the technologies mentioned above. It is recommended that the MTU for MS/TP be 1500 bytes [RFC8163]; the MTU in NB-IoT is 1600 bytes, and the maximum frame payload size for IEEE 802.11ah is 7991 bytes.

Using a larger MSS (to a suitable extent) may be beneficial in some scenarios, especially when transferring large payloads, as it reduces the number of packets (and packet headers) required for a given payload. However, the characteristics of the constrained network need to be considered. In particular, in a lossy network where unreliable fragment delivery is used, the amount of data that TCP unnecessarily retransmits due to fragment loss increases (and throughput decreases) quickly with the MSS. This happens because the loss of a fragment leads to the loss of the whole fragmented packet being transmitted. Unnecessary data retransmission is particularly harmful in CNNs due to the resource constraints of such environments. Note that, while the original 6LoWPAN fragmentation mechanism [RFC4944] does not offer reliable fragment delivery, fragment recovery functionality for 6LoWPAN or 6Lo environments has been standardized [RFC8931].

3.1.2. Explicit Congestion Notification (ECN)

ECN [RFC3168] allows a router to signal in the IP header of a packet that congestion is rising, for example, when a queue size reaches a certain threshold. An ECN-enabled TCP receiver will echo back the congestion signal to the TCP sender by setting a flag in its next TCP Acknowledgment (ACK). The sender triggers congestion control measures as if a packet loss had happened.

RFC 8087 [RFC8087] outlines the principal gains in terms of increased throughput, reduced delay, and other benefits when ECN is used over a network path that includes equipment that supports Congestion Experienced (CE) marking. In the context of CNNs, a remarkable feature of ECN is that congestion can be signaled without incurring packet drops (which will lead to retransmissions and consumption of limited resources such as energy and bandwidth).

ECN can further reduce packet losses since congestion control measures can be applied earlier [RFC2884]. Fewer lost packets implies that the number of retransmitted segments decreases, which is particularly beneficial in CNNs, where energy and bandwidth resources are typically limited. Also, it makes sense to try to avoid packet drops for transactional workloads with small data sizes, which are typical for CNNs. In such traffic patterns, it is more difficult and often impossible to detect packet loss without retransmission timeouts (e.g., as there may not be three duplicate ACKs). Any retransmission timeout slows down the data transfer significantly. In addition, if the constrained device uses power-saving techniques, a retransmission timeout will incur a wake-up action, in contrast to ACK clock-triggered sending. When the congestion window of a TCP sender has a size of one segment and a TCP ACK with an ECN signal (ECN-Echo (ECE) flag) arrives at the TCP sender, the TCP sender resets the retransmit timer, and the sender will only be able to send a new packet when the retransmit timer expires. Effectively, at that moment, the TCP sender reduces its sending rate from 1 segment per Round-Trip Time (RTT) to 1 segment per Retransmission Timeout (RTO) and reduces the sending rate further on each ECN signal received in subsequent TCP ACKs. Otherwise, if an ECN signal is not present in a subsequent TCP ACK, the TCP sender resumes the normal ACK-clocked transmission of segments [RFC3168].

ECN can be incrementally deployed in the Internet. Guidance on configuration and usage of ECN is provided in RFC 7567 [RFC7567]. Given the benefits, more and more TCP stacks in the Internet support ECN, and it makes sense to specifically leverage ECN in controlled environments such as CNNs. As of this writing, there is ongoing work to extend the types of TCP packets that are ECN capable, including pure ACKs [TCPM-ECN]. Such a feature may further increase the benefits of ECN in CNN environments. Note, however, that supporting ECN increases implementation complexity.

3.1.3. Explicit Loss Notifications

There has been a significant body of research on solutions capable of explicitly indicating whether a TCP segment loss is due to corruption, in order to avoid activation of congestion control mechanisms [ETEN] [RFC2757]. While such solutions may provide significant improvement, they have not been widely deployed and remain as experimental work. In fact, as of today, the IETF has not standardized any such solution.

3.2. TCP Guidance for Single-MSS Stacks

This section discusses TCP stacks that allow transferring a single MSS. More general guidance is provided in Section 3.3.

3.2.1. Single-MSS Stacks -- Benefits and Issues

A TCP stack can reduce the memory requirements by advertising a TCP window size of 1 MSS and also transmit, at most, 1 MSS of unacknowledged data. In that case, both congestion and flow control implementation are quite simple. Such a small receive and send window may be sufficient for simple message exchanges in the CNN space. However, only using a window of 1 MSS can significantly affect performance. A stop-and-wait operation results in low throughput for transfers that exceed the length of 1 MSS, e.g., a firmware download. Furthermore, a single-MSS solution relies solely on timer-based loss recovery, therefore missing the performance gain of Fast Retransmit and Fast Recovery (which requires a larger window size; see Section 3.3.1).

If CoAP is used over TCP with the default setting for NSTART in RFC 7252 [RFC7252], a CoAP endpoint is not allowed to send a new message to a destination until a response for the previous message sent to that destination has been received. This is equivalent to an application-layer window size of 1 data unit. For this use of CoAP, a maximum TCP window of 1 MSS may be sufficient, as long as the CoAP message size does not exceed 1 MSS. An exception in CoAP over TCP, though, is the Capabilities and Settings Message (CSM) that must be sent at the start of the TCP connection. The first application message carrying user data is allowed to be sent immediately after the CSM message. If the sum of the CSM size plus the application message size exceeds the MSS, a sender using a single-MSS stack will need to wait for the ACK confirming the CSM before sending the application message.

3.2.2. TCP Options for Single-MSS Stacks

A TCP implementation needs to support, at a minimum, TCP options 2, 1, and 0. These are, respectively, the MSS option, the No-Operation option, and the End Of Option List marker [RFC0793]. None of these are a substantial burden to support. These options are sufficient for interoperability with a standard-compliant TCP endpoint, albeit many TCP stacks support additional options and can negotiate their use. A TCP implementation is permitted to silently ignore all other TCP options.

A TCP implementation for a constrained device that uses a single-MSS TCP receive or transmit window size may not benefit from supporting the following TCP options: Window Scale [RFC7323], TCP Timestamps [RFC7323], Selective Acknowledgment (SACK) [RFC2018], and SACK-Permitted [RFC2018]. Also, other TCP options may not be required on a constrained device with a very lightweight implementation. With regard to the Window Scale option, note that it is only useful if a window size greater than 64 kB is needed.

Note that a TCP sender can benefit from the TCP Timestamps option [RFC7323] in detecting spurious RTOs. The latter are quite likely to occur in CNN scenarios due to a number of reasons (e.g., route changes in a multihop scenario, link-layer retries, etc.). The header overhead incurred by the Timestamps option (of up to 12 bytes) needs to be taken into account.

3.2.3. Delayed Acknowledgments for Single-MSS Stacks

TCP Delayed Acknowledgments are meant to reduce the number of ACKs sent within a TCP connection, thus reducing network overhead, but they may increase the time until a sender may receive an ACK. In general, usefulness of Delayed ACKs depends heavily on the usage scenario (see Section 3.3.2). There can be interactions with single-MSS stacks.

When traffic is unidirectional, if the sender can send at most 1 MSS of data or the receiver advertises a receive window not greater than the MSS, Delayed ACKs may unnecessarily contribute delay (up to 500 ms) to the RTT [RFC5681], which limits the throughput and can increase data delivery time. Note that, in some cases, it may not be possible to disable Delayed ACKs. One known workaround is to split the data to be sent into two segments of smaller size. A standard-compliant TCP receiver may immediately acknowledge the second MSS of data, which can improve throughput. However, this "split hack" may not always work since a TCP receiver is required to acknowledge every second full-sized segment, but not two consecutive small segments. The overhead of sending two IP packets instead of one is another downside of the "split hack".

Similar issues may happen when the sender uses the Nagle algorithm, since the sender may need to wait for an unnecessarily Delayed ACK to send a new segment. Disabling the algorithm will not have impact if the sender can only handle stop-and-wait operation at the TCP level.

For request-response traffic, when the receiver uses Delayed ACKs, a response to a data message can piggyback an ACK, as long as the latter is sent before the Delayed ACK timer expires, thus avoiding unnecessary ACKs without payload. Disabling Delayed ACKs at the request sender allows an immediate ACK for the data segment carrying the response.

3.2.4. RTO Calculation for Single-MSS Stacks

The RTO calculation is one of the fundamental TCP algorithms [RFC6298]. There is a fundamental trade-off: a short, aggressive RTO behavior reduces wait time before retransmissions, but it also increases the probability of spurious timeouts. The latter leads to unnecessary waste of potentially scarce resources in CNNs such as energy and bandwidth. In contrast, a conservative timeout can result in long error recovery times and, thus, needlessly delay data delivery.

If a TCP sender uses a very small window size, and it cannot benefit from Fast Retransmit and Fast Recovery or SACK, the RTO algorithm has a large impact on performance. In that case, RTO algorithm tuning may be considered, although careful assessment of possible drawbacks is recommended [RFC8961].

As an example, adaptive RTO algorithms defined for CoAP over UDP have been found to perform well in CNN scenarios [Commag] [CORE-FASOR].

3.3. General Recommendations for TCP in CNNs

This section summarizes some widely used techniques to improve TCP, with a focus on their use in CNNs. The TCP extensions discussed here are useful in a wide range of network scenarios, including CNNs. This section is not comprehensive. A comprehensive survey of TCP extensions is published in RFC 7414 [RFC7414].

3.3.1. Loss Recovery and Congestion/Flow Control

Devices that have enough memory to allow a larger (i.e., more than 3 MSS of data) TCP window size can leverage a more efficient loss recovery than the timer-based approach used for a smaller TCP window size (see Section 3.2.1) by using Fast Retransmit and Fast Recovery [RFC5681], at the expense of slightly greater complexity and Transmission Control Block (TCB) size. Assuming that Delayed ACKs are used by the receiver, a window size of up to 5 MSS is required for Fast Retransmit and Fast Recovery to work efficiently: in a given TCP transmission of full-sized segments 1, 2, 3, 4, and 5, if segment 2 gets lost, and the ACK for segment 1 is held by the Delayed ACK timer, then the sender should get an ACK for segment 1 when 3 arrives and duplicate ACKs when segments 4, 5, and 6 arrive. It will retransmit segment 2 when the third duplicate ACK arrives. In order to have segments 2, 3, 4, 5, and 6 sent, the window has to be of at least 5 MSS. With an MSS of 1220 bytes, a buffer of a size of 5 MSS would require 6100 bytes.

The example in the previous paragraph did not use a further TCP improvement such as Limited Transmit [RFC3042]. The latter may also be useful for any transfer that has more than one segment in flight. Small transfers tend to benefit more from Limited Transmit, because they are more likely to not receive enough duplicate ACKs. Assuming the example in the previous paragraph, Limited Transmit allows sending 5 MSS with a congestion window (cwnd) of three segments, plus two additional segments for the first two duplicate ACKs. With Limited Transmit, even a cwnd of two segments allows sending 5 MSS, at the expense of additional delay contributed by the Delayed ACK timer for the ACK that confirms segment 1.

When a multiple-segment window is used, the receiver will need to manage the reception of possible out-of-order received segments, requiring sufficient buffer space. Note that even when a window of 1 MSS is used, out-of-order arrival should also be managed, as the sender may send multiple sub-MSS packets that fit in the window. (On the other hand, the receiver is free to simply drop out-of-order segments, thus forcing retransmissions.)

3.3.1.1. Selective Acknowledgments (SACKs)

If a device with less severe memory and processing constraints can afford advertising a TCP window size of several MSSs, it makes sense to support the SACK option to improve performance. SACK allows a data receiver to inform the data sender of non-contiguous data blocks received, thus a sender (having previously sent the SACK-Permitted option) can avoid performing unnecessary retransmissions, saving energy and bandwidth, as well as reducing latency. In addition, SACK often allows for faster loss recovery when there is more than one lost segment in a window of data, since SACK recovery may complete with less RTTs. SACK is particularly useful for bulk data transfers. A receiver supporting SACK will need to keep track of the data blocks that need to be received. The sender will also need to keep track of which data segments need to be resent after learning which data blocks are missing at the receiver. SACK adds 8*n+2 bytes to the TCP header, where n denotes the number of data blocks received, up to four blocks. For a low number of out-of-order segments, the header overhead penalty of SACK is compensated by avoiding unnecessary retransmissions. When the sender discovers the data blocks that have already been received, it needs to also store the necessary state to avoid unnecessary retransmission of data segments that have already been received.

3.3.2. Delayed Acknowledgments

For certain traffic patterns, Delayed ACKs may have a detrimental effect, as already noted in Section 3.2.3. Advanced TCP stacks may use heuristics to determine the maximum delay for an ACK. For CNNs, the recommendation depends on the expected communication patterns.

When traffic over a CNN is expected mostly to be unidirectional messages with a size typically up to 1 MSS, and the time between two consecutive message transmissions is greater than the Delayed ACK timeout, it may make sense to use a smaller timeout or disable Delayed ACKs at the receiver. This avoids incurring additional delay, as well as the energy consumption of the sender (which might, e.g., keep its radio interface in receive mode) during that time. Note that disabling Delayed ACKs may only be possible if the peer device is administered by the same entity managing the constrained device. For request-response traffic, enabling Delayed ACKs is recommended at the server end, in order to allow combining a response with the ACK into a single segment, thus increasing efficiency. In addition, if a client issues requests infrequently, disabling Delayed ACKs at the client allows an immediate ACK for the data segment carrying the response.

In contrast, Delayed ACKs allow for a reduced number of ACKs in bulk transfer types of traffic, e.g., for firmware/software updates or for transferring larger data units containing a batch of sensor readings.

Note that, in many scenarios, the peer that a constrained device communicates with will be a general purpose system that communicates with both constrained and unconstrained devices. Since Delayed ACKs are often configured through system-wide parameters, the behavior of Delayed ACKs at the peer will be the same regardless of the nature of the endpoints it talks to. Such a peer will typically have Delayed ACKs enabled.

3.3.3. Initial Window

[RFC5681] specifies a TCP Initial Window (IW) of roughly 4 kB. Subsequently, RFC 6928 [RFC6928] defines an experimental new value for the IW, which in practice will result in an IW of 10 MSS. Nowadays, the latter is used in many TCP implementations.

Note that a 10-MSS IW was recommended for resource-rich environments (e.g., broadband environments), which are significantly different from CNNs. In CNNs, many application-layer data units are relatively small (e.g., below 1 MSS). However, larger objects (e.g., large files containing sensor readings, firmware updates, etc.) may also need to be transferred in CNNs. If such a large object is transferred in CNNs, with an IW setting of 10 MSS, there is significant buffer overflow risk, since many CNN devices support network or radio buffers of a size smaller than 10 MSS. In order to avoid such a problem, the IW needs to be carefully set in CNNs, based on device and network resource constraints. In many cases, a safe IW setting will be smaller than 10 MSS.

4. TCP Usage Recommendations in CNNs

This section discusses how TCP can be used by applications that are developed for CNN scenarios. These remarks are by and large independent of how TCP is exactly implemented.

4.1. TCP Connection Initiation

In the scenario of a constrained device to an unconstrained device illustrated above, a TCP connection is typically initiated by the constrained device, in order for the device to support possible sleep periods to save energy.

4.2. Number of Concurrent Connections

TCP endpoints with a small amount of memory may only support a small number of connections. Each TCP connection requires storing a number of variables in the TCB. Depending on the internal TCP implementation, each connection may result in further memory overhead, and connections may compete for scarce resources (e.g., further memory overhead for send and receive buffers, etc.).

A careful application design may try to keep the number of concurrent connections as small as possible. A client can, for instance, limit the number of simultaneous open connections that it maintains to a given server. Multiple connections could, for instance, be used to avoid the "head-of-line blocking" problem in an application transfer. However, in addition to consuming resources, using multiple connections can also cause undesirable side effects in congested networks. For example, the HTTP/1.1 specification encourages clients to be conservative when opening multiple connections [RFC7230]. Furthermore, each new connection will start with a three-way handshake, therefore increasing message overhead.

Being conservative when opening multiple TCP connections is of particular importance in Constrained-Node Networks.

4.3. TCP Connection Lifetime

In order to minimize message overhead, it makes sense to keep a TCP connection open as long as the two TCP endpoints have more data to send. If applications exchange data rather infrequently, i.e., if TCP connections would stay idle for a long time, the idle time can result in problems. For instance, certain middleboxes such as firewalls or NAT devices are known to delete state records after an inactivity interval. RFC 5382 [RFC5382] specifies a minimum value for such an interval of 124 minutes. Measurement studies have reported that TCP NAT binding timeouts are highly variable across devices, with the median being around 60 minutes, the shortest timeout being around 2 minutes, and more than 50% of the devices with a timeout shorter than the aforementioned minimum timeout of 124 minutes [HomeGateway]. The timeout duration used by a middlebox implementation may not be known to the TCP endpoints.

In CNNs, such middleboxes may, e.g., be present at the boundary between the CNN and other networks. If the middlebox can be optimized for CNN use cases, it makes sense to increase the initial value for filter state inactivity timers to avoid problems with idle connections. Apart from that, this problem can be dealt with by different connection-handling strategies, each having pros and cons.

One approach for infrequent data transfer is to use short-lived TCP connections. Instead of trying to maintain a TCP connection for a long time, it is possible that short-lived connections can be opened between two endpoints, which are closed if no more data needs to be exchanged. For use cases that can cope with the additional messages and the latency resulting from starting new connections, it is recommended to use a sequence of short-lived connections instead of maintaining a single long-lived connection.

The message and latency overhead that stems from using a sequence of short-lived connections could be reduced by TCP Fast Open (TFO) [RFC7413], which is an experimental TCP extension, at the expense of increased implementation complexity and increased TCB size. TFO allows data to be carried in SYN (and SYN-ACK) segments and to be consumed immediately by the receiving endpoint. This reduces the message and latency overhead compared to the traditional three-way handshake to establish a TCP connection. For security reasons, the connection initiator has to request a TFO cookie from the other endpoint. The cookie, with a size of 4 or 16 bytes, is then included in SYN packets of subsequent connections. The cookie needs to be refreshed (and obtained by the client) after a certain amount of time. While a given cookie is used for multiple connections between the same two endpoints, the latter may become vulnerable to privacy threats. In addition, a valid cookie may be stolen from a compromised host and may be used to perform SYN flood attacks, as well as amplified reflection attacks to victim hosts (see Section 5 of [RFC7413]). Nevertheless, TFO is more efficient than frequently opening new TCP connections with the traditional three-way handshake, as long as the cookie can be reused in subsequent connections. However, as stated in [RFC7413], TFO deviates from the standard TCP semantics, since the data in the SYN could be replayed to an application in some rare circumstances. Applications should not use TFO unless they can tolerate this issue, e.g., by using TLS [RFC7413]. A comprehensive discussion on TFO can be found in RFC 7413 [RFC7413].

Another approach is to use long-lived TCP connections with application-layer heartbeat messages. Various application protocols support such heartbeat messages (e.g., CoAP over TCP [RFC8323]). Periodic application-layer heartbeats can prevent early filter state record deletion in middleboxes. If the TCP binding timeout for a middlebox to be traversed by a given connection is known, middlebox filter state deletion will be avoided if the heartbeat period is lower than the middlebox TCP binding timeout. Otherwise, the implementer needs to take into account that middlebox TCP binding timeouts fall in a wide range of possible values [HomeGateway], and it may be hard to find a proper heartbeat period for application-layer heartbeat messages.

One specific advantage of heartbeat messages is that they also allow liveness checks at the application level. In general, it makes sense to realize liveness checks at the highest protocol layer possible that is meaningful to the application, in order to maximize the depth of the liveness check. In addition, timely detection of a dead peer may allow savings in terms of TCB memory use. However, the transmission of heartbeat messages consumes resources. This aspect needs to be assessed carefully, considering the characteristics of each specific CNN.

A TCP implementation may also be able to send "keep-alive" segments to test a TCP connection. According to [RFC1122], keep-alives are an optional TCP mechanism that is turned off by default, i.e., an application must explicitly enable it for a TCP connection. The interval between keep-alive messages must be configurable, and it must default to no less than two hours. With this large timeout, TCP keep-alive messages might not always be useful to avoid deletion of filter state records in some middleboxes. However, sending TCP keep-alive probes more frequently risks draining power on energy- constrained devices.

5. Security Considerations

Best current practices for securing TCP and TCP-based communication also applies to CNN. As an example, use of TLS [RFC8446] is strongly recommended if it is applicable. However, note that TLS protects only the contents of the data segments.

There are TCP options that can actually protect the transport layer. One example is the TCP Authentication Option (TCP-AO) [RFC5925]. However, this option adds overhead and complexity. TCP-AO typically has a size of 16-20 bytes. An implementer needs to asses the trade-off between security and performance when using TCP-AO, considering the characteristics (in terms of energy, bandwidth, and computational power) of the environment where TCP will be used.

For the mechanisms discussed in this document, the corresponding considerations apply. For instance, if TFO is used, the security considerations of RFC 7413 [RFC7413] apply.

Constrained devices are expected to support smaller TCP window sizes than less-limited devices. In such conditions, segment retransmission triggered by RTO expiration is expected to be relatively frequent, due to lack of (enough) duplicate ACKs, especially when a constrained device uses a single-MSS implementation. For this reason, constrained devices running TCP may appear as particularly appealing victims of the so-called "shrew" Denial-of-Service (DoS) attack [SHREW], whereby one or more sources generate a packet spike targeted to coincide with consecutive RTO-expiration-triggered retry attempts of a victim node. Note that the attack may be performed by Internet-connected devices, including constrained devices in the same CNN as the victim, as well as remote ones. Mitigation techniques include RTO randomization and attack blocking by routers able to detect shrew attacks based on their traffic pattern.

6. IANA Considerations

This document has no IANA actions.

7. References

7.1. Normative References

[RFC0793]
Postel, J., "Transmission Control Protocol", STD 7, RFC 793, DOI 10.17487/RFC0793, , <https://www.rfc-editor.org/info/rfc793>.
[RFC1122]
Braden, R., Ed., "Requirements for Internet Hosts - Communication Layers", STD 3, RFC 1122, DOI 10.17487/RFC1122, , <https://www.rfc-editor.org/info/rfc1122>.
[RFC2018]
Mathis, M., Mahdavi, J., Floyd, S., and A. Romanow, "TCP Selective Acknowledgment Options", RFC 2018, DOI 10.17487/RFC2018, , <https://www.rfc-editor.org/info/rfc2018>.
[RFC3042]
Allman, M., Balakrishnan, H., and S. Floyd, "Enhancing TCP's Loss Recovery Using Limited Transmit", RFC 3042, DOI 10.17487/RFC3042, , <https://www.rfc-editor.org/info/rfc3042>.
[RFC3168]
Ramakrishnan, K., Floyd, S., and D. Black, "The Addition of Explicit Congestion Notification (ECN) to IP", RFC 3168, DOI 10.17487/RFC3168, , <https://www.rfc-editor.org/info/rfc3168>.
[RFC5681]
Allman, M., Paxson, V., and E. Blanton, "TCP Congestion Control", RFC 5681, DOI 10.17487/RFC5681, , <https://www.rfc-editor.org/info/rfc5681>.
[RFC6298]
Paxson, V., Allman, M., Chu, J., and M. Sargent, "Computing TCP's Retransmission Timer", RFC 6298, DOI 10.17487/RFC6298, , <https://www.rfc-editor.org/info/rfc6298>.
[RFC6691]
Borman, D., "TCP Options and Maximum Segment Size (MSS)", RFC 6691, DOI 10.17487/RFC6691, , <https://www.rfc-editor.org/info/rfc6691>.
[RFC6928]
Chu, J., Dukkipati, N., Cheng, Y., and M. Mathis, "Increasing TCP's Initial Window", RFC 6928, DOI 10.17487/RFC6928, , <https://www.rfc-editor.org/info/rfc6928>.
[RFC7228]
Bormann, C., Ersue, M., and A. Keranen, "Terminology for Constrained-Node Networks", RFC 7228, DOI 10.17487/RFC7228, , <https://www.rfc-editor.org/info/rfc7228>.
[RFC7323]
Borman, D., Braden, B., Jacobson, V., and R. Scheffenegger, Ed., "TCP Extensions for High Performance", RFC 7323, DOI 10.17487/RFC7323, , <https://www.rfc-editor.org/info/rfc7323>.
[RFC7413]
Cheng, Y., Chu, J., Radhakrishnan, S., and A. Jain, "TCP Fast Open", RFC 7413, DOI 10.17487/RFC7413, , <https://www.rfc-editor.org/info/rfc7413>.
[RFC7567]
Baker, F., Ed. and G. Fairhurst, Ed., "IETF Recommendations Regarding Active Queue Management", BCP 197, RFC 7567, DOI 10.17487/RFC7567, , <https://www.rfc-editor.org/info/rfc7567>.
[RFC8200]
Deering, S. and R. Hinden, "Internet Protocol, Version 6 (IPv6) Specification", STD 86, RFC 8200, DOI 10.17487/RFC8200, , <https://www.rfc-editor.org/info/rfc8200>.

7.2. Informative References

[6LO-WLANAH]
Del Carpio Vega, L., Robles, M., and R. Morabito, "IPv6 over 802.11ah", Work in Progress, Internet-Draft, draft-delcarpio-6lo-wlanah-01, , <https://tools.ietf.org/html/draft-delcarpio-6lo-wlanah-01>.
[Commag]
Betzler, A., Gomez, C., Demirkol, I., and J. Paradells, "CoAP Congestion Control for the Internet of Things", IEEE Communications Magazine, Vol. 54, Issue 7, pp. 154-160, DOI 10.1109/MCOM.2016.7509394, , <https://doi.org/10.1109/MCOM.2016.7509394>.
[CORE-FASOR]
Jarvinen, I., Kojo, M., Raitahila, I., and Z. Cao, "Fast-Slow Retransmission Timeout and Congestion Control Algorithm for CoAP", Work in Progress, Internet-Draft, draft-ietf-core-fasor-01, , <https://tools.ietf.org/html/draft-ietf-core-fasor-01>.
[Dunk]
Dunkels, A., "Full TCP/IP for 8-Bit Architectures", MobiSys '03, pp. 85-98, DOI 10.1145/1066116.106611, , <https://doi.org/10.1145/1066116.106611>.
[ETEN]
Krishnan, R., Sterbenz, J., Eddy, W., and C. Partridge, "Explicit transport error notification (ETEN) for error-prone wireless and satellite networks", Computer Networks, DOI 10.1016/j.comnet.2004.06.012, , <https://doi.org/10.1016/j.comnet.2004.06.012>.
[GNRC]
Lenders, M., Kietzmann, P., Hahm, O., Petersen, H., Gündoğa, C., Baccelli, E., Schleiser, K., Schmidt, T., and M. Wählisch, "Connecting the World of Embedded Mobiles: The RIOT Approach to Ubiquitous Networking for the IoT", arXiv:1801.02833v1 [cs.NI], .
[HomeGateway]
Haetoenen, S., Nyrhinen, A., Eggert, L., Strowes, S., Sarolahti, P., and M. Kojo, "An Experimental Study of Home Gateway Characteristics", Proceedings of the 10th ACM SIGCOMM conference on Internet measurement, pp. 260-266, DOI 10.1145/1879141.1879174, , <https://doi.org/10.1145/1879141.1879174>.
[IntComp]
Gomez, C., Arcia-Moret, A., and J. Crowcroft, "TCP in the Internet of Things: from Ostracism to Prominence", IEEE Internet Computing, Vol. 22, Issue 1, pp. 29-41, DOI 10.1109/MIC.2018.112102200, , <https://doi.org/10.1109/MIC.2018.112102200>.
[MQTT]
ISO/IEC, "Information technology -- Message Queuing Telemetry Transport (MQTT) v3.1.1", ISO/IEC 20922:2016, .
[RFC2757]
Montenegro, G., Dawkins, S., Kojo, M., Magret, V., and N. Vaidya, "Long Thin Networks", RFC 2757, DOI 10.17487/RFC2757, , <https://www.rfc-editor.org/info/rfc2757>.
[RFC2884]
Hadi Salim, J. and U. Ahmed, "Performance Evaluation of Explicit Congestion Notification (ECN) in IP Networks", RFC 2884, DOI 10.17487/RFC2884, , <https://www.rfc-editor.org/info/rfc2884>.
[RFC3481]
Inamura, H., Ed., Montenegro, G., Ed., Ludwig, R., Gurtov, A., and F. Khafizov, "TCP over Second (2.5G) and Third (3G) Generation Wireless Networks", BCP 71, RFC 3481, DOI 10.17487/RFC3481, , <https://www.rfc-editor.org/info/rfc3481>.
[RFC3819]
Karn, P., Ed., Bormann, C., Fairhurst, G., Grossman, D., Ludwig, R., Mahdavi, J., Montenegro, G., Touch, J., and L. Wood, "Advice for Internet Subnetwork Designers", BCP 89, RFC 3819, DOI 10.17487/RFC3819, , <https://www.rfc-editor.org/info/rfc3819>.
[RFC4944]
Montenegro, G., Kushalnagar, N., Hui, J., and D. Culler, "Transmission of IPv6 Packets over IEEE 802.15.4 Networks", RFC 4944, DOI 10.17487/RFC4944, , <https://www.rfc-editor.org/info/rfc4944>.
[RFC5382]
Guha, S., Ed., Biswas, K., Ford, B., Sivakumar, S., and P. Srisuresh, "NAT Behavioral Requirements for TCP", BCP 142, RFC 5382, DOI 10.17487/RFC5382, , <https://www.rfc-editor.org/info/rfc5382>.
[RFC5925]
Touch, J., Mankin, A., and R. Bonica, "The TCP Authentication Option", RFC 5925, DOI 10.17487/RFC5925, , <https://www.rfc-editor.org/info/rfc5925>.
[RFC6077]
Papadimitriou, D., Ed., Welzl, M., Scharf, M., and B. Briscoe, "Open Research Issues in Internet Congestion Control", RFC 6077, DOI 10.17487/RFC6077, , <https://www.rfc-editor.org/info/rfc6077>.
[RFC6120]
Saint-Andre, P., "Extensible Messaging and Presence Protocol (XMPP): Core", RFC 6120, DOI 10.17487/RFC6120, , <https://www.rfc-editor.org/info/rfc6120>.
[RFC6282]
Hui, J., Ed. and P. Thubert, "Compression Format for IPv6 Datagrams over IEEE 802.15.4-Based Networks", RFC 6282, DOI 10.17487/RFC6282, , <https://www.rfc-editor.org/info/rfc6282>.
[RFC6550]
Winter, T., Ed., Thubert, P., Ed., Brandt, A., Hui, J., Kelsey, R., Levis, P., Pister, K., Struik, R., Vasseur, JP., and R. Alexander, "RPL: IPv6 Routing Protocol for Low-Power and Lossy Networks", RFC 6550, DOI 10.17487/RFC6550, , <https://www.rfc-editor.org/info/rfc6550>.
[RFC6606]
Kim, E., Kaspar, D., Gomez, C., and C. Bormann, "Problem Statement and Requirements for IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) Routing", RFC 6606, DOI 10.17487/RFC6606, , <https://www.rfc-editor.org/info/rfc6606>.
[RFC6775]
Shelby, Z., Ed., Chakrabarti, S., Nordmark, E., and C. Bormann, "Neighbor Discovery Optimization for IPv6 over Low-Power Wireless Personal Area Networks (6LoWPANs)", RFC 6775, DOI 10.17487/RFC6775, , <https://www.rfc-editor.org/info/rfc6775>.
[RFC7230]
Fielding, R., Ed. and J. Reschke, Ed., "Hypertext Transfer Protocol (HTTP/1.1): Message Syntax and Routing", RFC 7230, DOI 10.17487/RFC7230, , <https://www.rfc-editor.org/info/rfc7230>.
[RFC7252]
Shelby, Z., Hartke, K., and C. Bormann, "The Constrained Application Protocol (CoAP)", RFC 7252, DOI 10.17487/RFC7252, , <https://www.rfc-editor.org/info/rfc7252>.
[RFC7414]
Duke, M., Braden, R., Eddy, W., Blanton, E., and A. Zimmermann, "A Roadmap for Transmission Control Protocol (TCP) Specification Documents", RFC 7414, DOI 10.17487/RFC7414, , <https://www.rfc-editor.org/info/rfc7414>.
[RFC7428]
Brandt, A. and J. Buron, "Transmission of IPv6 Packets over ITU-T G.9959 Networks", RFC 7428, DOI 10.17487/RFC7428, , <https://www.rfc-editor.org/info/rfc7428>.
[RFC7540]
Belshe, M., Peon, R., and M. Thomson, Ed., "Hypertext Transfer Protocol Version 2 (HTTP/2)", RFC 7540, DOI 10.17487/RFC7540, , <https://www.rfc-editor.org/info/rfc7540>.
[RFC7668]
Nieminen, J., Savolainen, T., Isomaki, M., Patil, B., Shelby, Z., and C. Gomez, "IPv6 over BLUETOOTH(R) Low Energy", RFC 7668, DOI 10.17487/RFC7668, , <https://www.rfc-editor.org/info/rfc7668>.
[RFC8087]
Fairhurst, G. and M. Welzl, "The Benefits of Using Explicit Congestion Notification (ECN)", RFC 8087, DOI 10.17487/RFC8087, , <https://www.rfc-editor.org/info/rfc8087>.
[RFC8105]
Mariager, P., Petersen, J., Ed., Shelby, Z., Van de Logt, M., and D. Barthel, "Transmission of IPv6 Packets over Digital Enhanced Cordless Telecommunications (DECT) Ultra Low Energy (ULE)", RFC 8105, DOI 10.17487/RFC8105, , <https://www.rfc-editor.org/info/rfc8105>.
[RFC8163]
Lynn, K., Ed., Martocci, J., Neilson, C., and S. Donaldson, "Transmission of IPv6 over Master-Slave/Token-Passing (MS/TP) Networks", RFC 8163, DOI 10.17487/RFC8163, , <https://www.rfc-editor.org/info/rfc8163>.
[RFC8201]
McCann, J., Deering, S., Mogul, J., and R. Hinden, Ed., "Path MTU Discovery for IP version 6", STD 87, RFC 8201, DOI 10.17487/RFC8201, , <https://www.rfc-editor.org/info/rfc8201>.
[RFC8323]
Bormann, C., Lemay, S., Tschofenig, H., Hartke, K., Silverajan, B., and B. Raymor, Ed., "CoAP (Constrained Application Protocol) over TCP, TLS, and WebSockets", RFC 8323, DOI 10.17487/RFC8323, , <https://www.rfc-editor.org/info/rfc8323>.
[RFC8352]
Gomez, C., Kovatsch, M., Tian, H., and Z. Cao, Ed., "Energy-Efficient Features of Internet of Things Protocols", RFC 8352, DOI 10.17487/RFC8352, , <https://www.rfc-editor.org/info/rfc8352>.
[RFC8376]
Farrell, S., Ed., "Low-Power Wide Area Network (LPWAN) Overview", RFC 8376, DOI 10.17487/RFC8376, , <https://www.rfc-editor.org/info/rfc8376>.
[RFC8446]
Rescorla, E., "The Transport Layer Security (TLS) Protocol Version 1.3", RFC 8446, DOI 10.17487/RFC8446, , <https://www.rfc-editor.org/info/rfc8446>.
[RFC8900]
Bonica, R., Baker, F., Huston, G., Hinden, R., Troan, O., and F. Gont, "IP Fragmentation Considered Fragile", BCP 230, RFC 8900, DOI 10.17487/RFC8900, , <https://www.rfc-editor.org/info/rfc8900>.
[RFC8931]
Thubert, P., Ed., "IPv6 over Low-Power Wireless Personal Area Network (6LoWPAN) Selective Fragment Recovery", RFC 8931, DOI 10.17487/RFC8931, , <https://www.rfc-editor.org/info/rfc8931>.
[RFC8961]
Allman, M., "Requirements for Time-Based Loss Detection", BCP 233, RFC 8961, DOI 10.17487/RFC8961, , <https://www.rfc-editor.org/info/rfc8961>.
[RIOT]
Baccelli, E., Gündoğa, C., Hahm, O., Kietzmann, P., Lenders, M., Petersen, H., Schleiser, K., Schmidt, T., and M. Wählisch, "RIOT: An Open Source Operating System for Low-End Embedded Devices in the IoT", IEEE Internet of Things Journal, Vol. 5, Issue 6, DOI 10.1109/JIOT.2018.2815038, , <https://doi.org/10.1109/JIOT.2018.2815038>.
[SHREW]
Nyrhinen, A. and E. Knightly, "Low-Rate TCP-Targeted Denial of Service Attacks (The Shrew vs. the Mice and Elephants)", SIGCOMM'03, DOI 10.1145/863955.863966, , <https://doi.org/10.1145/863955.863966>.
[TCPM-ECN]
Bagnulo, M. and B. Briscoe, "ECN++: Adding Explicit Congestion Notification (ECN) to TCP Control Packets", Work in Progress, Internet-Draft, draft-ietf-tcpm-generalized-ecn-07, , <https://tools.ietf.org/html/draft-ietf-tcpm-generalized-ecn-07>.

Appendix A. TCP Implementations for Constrained Devices

This section overviews the main features of TCP implementations for constrained devices. The survey is limited to open-source stacks with a small footprint. It is not meant to be all-encompassing. For more powerful embedded systems (e.g., with 32-bit processors), there are further stacks that comprehensively implement TCP. On the other hand, please be aware that this Annex is based on information available as of the writing.

A.1. uIP

uIP is a TCP/IP stack, targeted for 8- and 16-bit microcontrollers, which pioneered TCP/IP implementations for constrained devices. uIP has been deployed with Contiki and the Arduino Ethernet shield. A code size of ~5 kB (which comprises checksumming, IPv4, ICMP, and TCP) has been reported for uIP [Dunk]. Later versions of uIP implement IPv6 as well.

uIP uses the same global buffer for both incoming and outgoing traffic, which has a size of a single packet. In case of a retransmission, an application must be able to reproduce the same user data that had been transmitted. Multiple connections are supported but need to share the global buffer.

The MSS is announced via the MSS option on connection establishment, and the receive window size (of 1 MSS) is not modified during a connection. Stop-and-wait operation is used for sending data. Among other optimizations, this allows for the avoidance of sliding window operations, which use 32-bit arithmetic extensively and are expensive on 8-bit CPUs.

Contiki uses the "split hack" technique (see Section 3.2.3) to avoid Delayed ACKs for senders using a single segment.

The code size of the TCP implementation in Contiki-NG has been measured to be 3.2 kB on CC2538DK, cross-compiling on Linux.

A.2. lwIP

lwIP is a TCP/IP stack, targeted for 8- and 16-bit microcontrollers. lwIP has a total code size of ~14 kB to ~22 kB (which comprises memory management, checksumming, network interfaces, IPv4, ICMP, and TCP) and a TCP code size of ~9 kB to ~14 kB [Dunk]. Both IPv4 and IPv6 are supported in lwIP since v2.0.0.

In contrast with uIP, lwIP decouples applications from the network stack. lwIP supports a TCP transmission window greater than a single segment, as well as the buffering of incoming and outgoing data. Other implemented mechanisms comprise slow start, congestion avoidance, fast retransmit, and fast recovery. SACK and Window Scale support has been recently added to lwIP.

A.3. RIOT

The RIOT TCP implementation (called "GNRC TCP") has been designed for Class 1 devices [RFC7228]. The main target platforms are 8- and 16-bit microcontrollers, with 32-bit platforms also supported. GNRC TCP offers a similar function set as uIP, but it provides and maintains an independent receive buffer for each connection. In contrast to uIP, retransmission is also handled by GNRC TCP. For simplicity, GNRC TCP uses a single-MSS implementation. The application programmer does not need to know anything about the TCP internals; therefore, GNRC TCP can be seen as a user-friendly uIP TCP implementation.

The MSS is set on connections establishment and cannot be changed during connection lifetime. GNRC TCP allows multiple connections in parallel, but each TCB must be allocated somewhere in the system. By default, there is only enough memory allocated for a single TCP connection, but it can be increased at compile time if the user needs multiple parallel connections.

The RIOT TCP implementation offers an optional Portable Operating System Interface (POSIX) socket wrapper that enables POSIX compliance, if needed.

Further details on RIOT and GNRC can be found in [RIOT] and [GNRC].

A.4. TinyOS

TinyOS was important as a platform for early constrained devices. TinyOS has an experimental TCP stack that uses a simple non-blocking library-based implementation of TCP, which provides a subset of the socket interface primitives. The application is responsible for buffering. The TCP library does not do any receive-side buffering. Instead, it will immediately dispatch new, in-order data to the application or otherwise drop the segment. A send buffer is provided by the application. Multiple TCP connections are possible. Recently, there has been little work on the stack.

A.5. FreeRTOS

FreeRTOS is a real-time operating system kernel for embedded devices that is supported by 16- and 32-bit microprocessors. Its TCP implementation is based on multiple-segment window size, although a "Tiny-TCP" option, which is a single-MSS variant, can be enabled. Delayed ACKs are supported, with a 20 ms Delayed ACK timer as a technique intended "to gain performance".

A.6. uC/OS

uC/OS is a real-time operating system kernel for embedded devices, which is maintained by Micrium.  uC/OS is intended for 8-, 16-, and 32-bit microprocessors. The uC/OS TCP implementation supports a multiple-segment window size.

A.7. Summary

None of the implementations considered in this Annex support ECN or TFO.

Table 1: Summary of TCP Features for Different Lightweight TCP Implementations
uIP lwIP orig lwIP 2.1 RIOT TinyOS FreeRTOS uC/OS
Code Size (kB) <5 ~9 to ~14 38 <7 N/A <9.2 N/A
Memory (a) (T1) (T4) (T3) N/A (T2) N/A
TCP Features
Single-Segm. Yes No No Yes No No No
Slow start No Yes Yes No Yes No Yes
Fast rec/retx No Yes Yes No Yes No Yes
Keep-alive No No Yes No No Yes Yes
Win. Scale No No Yes No No Yes No
TCP timest. No No Yes No No Yes No
SACK No No Yes No No Yes No
Del. ACKs No Yes Yes No No Yes Yes
Socket No No Optional (I) Subset Yes Yes
Concur. Conn. Yes Yes Yes Yes Yes Yes Yes
TLS supported No No Yes Yes Yes Yes Yes

Legend:

(T1):
TCP-only, on x86 and AVR platforms
(T2):
TCP-only, on ARM Cortex-M platform
(T3):
TCP-only, on ARM Cortex-M0+ platform (NOTE: RAM usage for the same platform is ~2.5 kB for one TCP connection plus ~1.2 kB for each additional connection)
(T4):
TCP-only, on CC2538DK, cross-compiling on Linux
(a):
Includes IP, ICMP, and TCP on x86 and AVR platforms. The Contiki-NG TCP implementation has a code size of 3.2 kB on CC2538DK, cross-compiling on Linux
(I):
Optional POSIX socket wrapper that enables POSIX compliance if needed
Mult.:
Multiple
N/A:
Not Available

Acknowledgments

The work of Carles Gomez has been funded in part by the Spanish Government (Ministerio de Educacion, Cultura y Deporte) through Jose Castillejo grants CAS15/00336 and CAS18/00170; the European Regional Development Fund (ERDF); the Spanish Government through projects TEC2016-79988-P, PID2019-106808RA-I00, AEI/FEDER, and UE; and the Generalitat de Catalunya Grant 2017 SGR 376. Part of his contribution to this work has been carried out during his stays as a visiting scholar at the Computer Laboratory of the University of Cambridge.

The authors appreciate the feedback received for this document. The following folks provided comments that helped improve the document: Carsten Bormann, Zhen Cao, Wei Genyu, Ari Keränen, Abhijan Bhattacharyya, Andres Arcia-Moret, Yoshifumi Nishida, Joe Touch, Fred Baker, Nik Sultana, Kerry Lynn, Erik Nordmark, Markku Kojo, Hannes Tschofenig, David Black, Ilpo Jarvinen, Emmanuel Baccelli, Stuart Cheshire, Gorry Fairhurst, Ingemar Johansson, Ted Lemon, and Michael Tüxen. Simon Brummer provided details and kindly performed Random Access Memory (RAM) and Read-Only Memory (ROM) usage measurements on the RIOT TCP implementation. Xavi Vilajosana provided details on the OpenWSN TCP implementation. Rahul Jadhav kindly performed code size measurements on the Contiki-NG and lwIP 2.1.2 TCP implementations. He also provided details on the uIP TCP implementation.

Authors' Addresses

Carles Gomez
UPC
C/Esteve Terradas, 7
08860 Castelldefels
Spain
Jon Crowcroft
University of Cambridge
JJ Thomson Avenue
Cambridge
CB3 0FD
United Kingdom
Michael Scharf
Hochschule Esslingen
University of Applied Sciences
Flandernstr. 101
73732 Esslingen am Neckar
Germany