patch-2.4.19 linux-2.4.19/arch/ppc/boot/mbx/iic.c

• Lines: 219
• Date: Wed Dec 31 16:00:00 1969
• Orig file: linux-2.4.18/arch/ppc/boot/mbx/iic.c
• Orig date: Mon Oct 8 11:40:13 2001

diff -urN linux-2.4.18/arch/ppc/boot/mbx/iic.c linux-2.4.19/arch/ppc/boot/mbx/iic.c
@@ -1,218 +0,0 @@
-/*
- * BK Id: SCCS/s.iic.c 1.10 09/14/01 19:30:13 trini
- */
-
-/* Minimal support functions to read configuration from IIC EEPROMS
- * on MPC8xx boards.  Originally written for RPGC RPX-Lite.
- * Dan Malek (dmalek@jlc.net).
- */
-#include <linux/types.h>
-#include <asm/uaccess.h>
-#include <asm/mpc8xx.h>
-#include <asm/commproc.h>
-
-
-/* IIC functions.
- * These are just the basic master read/write operations so we can
- * examine serial EEPROM.
- */
-void	iic_read(uint devaddr, u_char *buf, uint offset, uint count);
-
-static	int	iic_init_done;
-
-static void
-iic_init()
-{
-	volatile iic_t *iip;
-	volatile i2c8xx_t *i2c;
-	volatile cpm8xx_t	*cp;
-	volatile immap_t	*immap;
-	uint	dpaddr;
-
-	immap = (immap_t *)IMAP_ADDR;
-	cp = (cpm8xx_t *)&(immap->im_cpm);
-
-	/* Reset the CPM.  This is necessary on the 860 processors
-	 * that may have started the SCC1 ethernet without relocating
-	 * the IIC.
-	 * This also stops the Ethernet in case we were loaded by a
-	 * BOOTP rom monitor.
-	 */
-	cp->cp_cpcr = (CPM_CR_RST | CPM_CR_FLG);
-
-	/* Wait for it.
-	*/
-	while (cp->cp_cpcr & (CPM_CR_RST | CPM_CR_FLG));
-
-	/* Remove any microcode patches.  We will install our own
-	 * later.
-	 */
-	cp->cp_cpmcr1 = 0;
-	cp->cp_cpmcr2 = 0;
-	cp->cp_cpmcr3 = 0;
-	cp->cp_cpmcr4 = 0;
-	cp->cp_rccr = 0;
-
-	iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
-	i2c = (i2c8xx_t *)&(immap->im_i2c);
-
-	/* Initialize Port B IIC pins.
-	*/
-	cp->cp_pbpar |= 0x00000030;
-	cp->cp_pbdir |= 0x00000030;
-	cp->cp_pbodr |= 0x00000030;
-
-	/* Initialize the parameter ram.
-	*/
-
-	/* Allocate space for a two transmit and one receive buffer
-	 * descriptor in the DP ram.
-	 * For now, this address seems OK, but it may have to
-	 * change with newer versions of the firmware.
-	 */
-	dpaddr = 0x0840;
-
-	/* Set up the IIC parameters in the parameter ram.
-	*/
-	iip->iic_tbase = dpaddr;
-	iip->iic_rbase = dpaddr + (2 * sizeof(cbd_t));
-
-	iip->iic_tfcr = SMC_EB;
-	iip->iic_rfcr = SMC_EB;
-
-	/* This should really be done by the reader/writer.
-	*/
-	iip->iic_mrblr = 128;
-
-	/* Initialize Tx/Rx parameters.
-	*/
-	cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_I2C, CPM_CR_INIT_TRX) | CPM_CR_FLG;
-	while (cp->cp_cpcr & CPM_CR_FLG);
-
-	/* Select an arbitrary address.  Just make sure it is unique.
-	*/
-	i2c->i2c_i2add = 0x34;
-
-	/* Make clock run maximum slow.
-	*/
-	i2c->i2c_i2brg = 7;
-
-	/* Disable interrupts.
-	*/
-	i2c->i2c_i2cmr = 0;
-	i2c->i2c_i2cer = 0xff;
-
-	/* Enable SDMA.
-	*/
-	immap->im_siu_conf.sc_sdcr = 1;
-
-	iic_init_done = 1;
-}
-
-/* Read from IIC.
- * Caller provides device address, memory buffer, and byte count.
- */
-static	u_char	iitemp[32];
-
-void
-iic_read(uint devaddr, u_char *buf, uint offset, uint count)
-{
-	volatile iic_t		*iip;
-	volatile i2c8xx_t	*i2c;
-	volatile cbd_t		*tbdf, *rbdf;
-	volatile cpm8xx_t	*cp;
-	volatile immap_t	*immap;
-	u_char			*tb;
-	uint			temp;
-
-	/* If the interface has not been initialized, do that now.
-	*/
-	if (!iic_init_done)
-		iic_init();
-
-	immap = (immap_t *)IMAP_ADDR;
-	cp = (cpm8xx_t *)&(immap->im_cpm);
-
-	iip = (iic_t *)&cp->cp_dparam[PROFF_IIC];
-	i2c = (i2c8xx_t *)&(immap->im_i2c);
-
-	tbdf = (cbd_t *)&cp->cp_dpmem[iip->iic_tbase];
-	rbdf = (cbd_t *)&cp->cp_dpmem[iip->iic_rbase];
-
-	/* Send a "dummy write" operation.  This is a write request with
-	 * only the offset sent, followed by another start condition.
-	 * This will ensure we start reading from the first location
-	 * of the EEPROM.
-	 */
-	tb = iitemp;
-	tb = (u_char *)(((uint)tb + 15) & ~15);
-	tbdf->cbd_bufaddr = (int)tb;
-	*tb = devaddr & 0xfe;	/* Device address */
-	*(tb+1) = offset;		/* Offset */
-	tbdf->cbd_datlen = 2;		/* Length */
-	tbdf->cbd_sc =
-	      BD_SC_READY | BD_SC_LAST | BD_SC_WRAP | BD_IIC_START;
-
-	i2c->i2c_i2mod = 1;	/* Enable */
-	i2c->i2c_i2cer = 0xff;
-	i2c->i2c_i2com = 0x81;	/* Start master */
-
-	/* Wait for IIC transfer.
-	*/
-#if 0
-	while ((i2c->i2c_i2cer & 3) == 0);
-
-	if (tbdf->cbd_sc & BD_SC_READY)
-		printf("IIC ra complete but tbuf ready\n");
-#else
-	temp = 10000000;
-	while ((tbdf->cbd_sc & BD_SC_READY) && (temp != 0))
-		temp--;
-#if 0
-	/* We can't do this...there is no serial port yet!
-	*/
-	if (temp == 0) {
-		printf("Timeout reading EEPROM\n");
-		return;
-	}
-#endif
-#endif
-	
-	/* Chip errata, clear enable.
-	*/
-	i2c->i2c_i2mod = 0;
-
-	/* To read, we need an empty buffer of the proper length.
-	 * All that is used is the first byte for address, the remainder
-	 * is just used for timing (and doesn't really have to exist).
-	 */
-	tbdf->cbd_bufaddr = (int)tb;
-	*tb = devaddr | 1;	/* Device address */
-	rbdf->cbd_bufaddr = (uint)buf;		/* Desination buffer */
-	tbdf->cbd_datlen = rbdf->cbd_datlen = count + 1;	/* Length */
-	tbdf->cbd_sc = BD_SC_READY | BD_SC_LAST | BD_SC_WRAP | BD_IIC_START;
-	rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP;
-
-	/* Chip bug, set enable here.
-	*/
-	i2c->i2c_i2mod = 1;	/* Enable */
-	i2c->i2c_i2cer = 0xff;
-	i2c->i2c_i2com = 0x81;	/* Start master */
-
-	/* Wait for IIC transfer.
-	*/
-#if 0
-	while ((i2c->i2c_i2cer & 1) == 0);
-
-	if (rbdf->cbd_sc & BD_SC_EMPTY)
-		printf("IIC read complete but rbuf empty\n");
-#else
-	temp = 10000000;
-	while ((tbdf->cbd_sc & BD_SC_READY) && (temp != 0))
-		temp--;
-#endif
-	
-	/* Chip errata, clear enable.
-	*/
-	i2c->i2c_i2mod = 0;
-}